Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopen®, which make them easily scalable to meet requirements for both.

Author: Mooguzragore Tegul
Country: Indonesia
Language: English (Spanish)
Genre: Software
Published (Last): 20 August 2011
Pages: 483
PDF File Size: 16.15 Mb
ePub File Size: 8.70 Mb
ISBN: 472-2-88717-467-3
Downloads: 45048
Price: Free* [*Free Regsitration Required]
Uploader: Goltijin

Both groups can be configured either as a current input or as a voltage input. Applies to inputs used as normal digital inputs. All claims with respect to defects in the products shall be made to the manufacturer without delay and no later than on the seventh 7th day after the defect has been or should have been discovered by the buyer. Maximum pulse input frequency 20 kHz.

The Mini module and the Mini display need the Hub module in order to have the full transient immunity. Closed loops wiring can be achieved by connecting the GND wire from the rpec, actuator etc.

These parameters depend on software cycle time Note 5: Is dependable for the other interrupt load in module for example heavy CAN-traffic can reduce maximum frequency.

Inputs are divided into groups by the input impedance configuration. Any of these inputs can be logically paired with another similar input.

Maximum code size kb.

Violating this rating may lead to system not recognizing all input state transitions Note 3: For example, if group two is configured as a current input, then both pins X3. The manufacturer does not assume any responsibility for this product being fit for any particular application, unless otherwise expressly stated in writing by the manufacturer.

  ENFERMEDAD DE MINAMATA PDF

The manufacturer gives no other warranties whatsoever for the products than the warranty set out in this section and thus the warranty given in this section sets forth the warranty given by the manufacturer in its entirety. This product is designed to be used only for machine controlling purposes.

In PLCopen programming environment, there is a word variable in IW area associated with each pin from where the software can read the actual current flowing into the pin.

EPEC controller Manual _Download Manual

Test method EN ? The manufacturer strives to reply to the claim in writing within two epfc weeks from the receipt of the claim. In carefully selected applications these pins can also be used as digital inputs.

There are three variables associated with each pin of this type in IEC programming environment. Puncture hole fastening 7. Violating this rating may lead to incorrect measurement or counting Note 7: In other words, pins connect the load to the ground. Closed light cast aluminium housing? The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc.

EPEC E3002024-20 PLC-SET 2024 SPT-K-2024EPEC EPEC2024 2023

In PLCopen programming environment, there is a word variable in IW area associated with each pin from where the software can read the actual signal magnitude at the pin.

Module has a shutdown circuit which protects the module and loads against dpec.

For more information refer to programming manuals. A small and protective module casing keeps inside high performance microcontroller with lots of control capabilities.

Excavator Spare Parts for SANY EPEC 2024 Control Module

The warranty does not cover any costs related to removing or fastening of devices related to the products. Module temperature Software deadlock is monitored by the hardware watchdog that reboots the module automatically after ms software deadlock. With input voltages below 4,3 V it seems like the internal input resistance was connected to a 1,3 V voltage source Note 2: The other two are word variables in the IW memory area which hold the frequency value and the number of pulses.

  ALPINE SWR-1242D PDF

The manufacturer shall, at its sole option, repair the products at its manufactory in Sein? Violating this rating may lead to system not recognizing all input state transitions Note 4: Pins of this kind are used to measure analog signals.

If separate Epec module shock protection cover E is mounted, it is recommended to use Epec E fastening bolts? Neither does the warranty cover the expenses of sending dpec to or from the manufacturer for repairs. The setting is done by a PWM channel but setting the frequency of one channel sets also the frequencies of all the other channels in the same groups.

Programming environment CoDeSys 2. It must be taken care in system design that the output unintentionally switching to on state causes no harm to the system. Violating this rating may lead to system not recognizing all input state transitions Note 2: Violating this rating may lead to system not recognizing all input state transitions.

All functions return automatically to within normal limits after exposure is removed.