EKC 202D1 PDF

Buy B DANFOSS REFRIGERATION EKC D1, ller, I-pack the best price, fast worldwide shipping, up to 65% discount DANFOSS. EKC controllers can be used for a wide range of different refrigeration applications .. Regolatore per il controllo della temperatura – EKC D1, Literature. I need some help on this danfoss EKC D1. Its controlling a small freezer unit The set-point temperature is º The R1 seting is diferential is.

Author: Samuzahn Douzil
Country: Pakistan
Language: English (Spanish)
Genre: Technology
Published (Last): 3 February 2017
Pages: 387
PDF File Size: 17.39 Mb
ePub File Size: 11.3 Mb
ISBN: 676-8-35112-387-2
Downloads: 18074
Price: Free* [*Free Regsitration Required]
Uploader: Faekora

Push the middle button again to freeze the value. After the setting the value will return to 0. Drip-off time Here you set the time that is to elapse from a defrost and until the compressor is to start again.

Controles de temperatura para muebles y cámaras frigoríficas – Documentos

DI1 and DI2 are contact functions that can be used for one of the following functions: There will be re-start at 2 K below the setting. Real-time clock The controller can accommodate one insertion module which may either be a data communication module or a battery module for the real-time clock.

When the input is short-circuited, there will be regulation for night operation. Select your own number. When the compressor is operating it must run for at least x minutes.

The relevant application determines how. Fan delay — water attaches to the evaporator 15 S Here you can set the time delay. Here the signal may be used by the defrost function, so that the shortest and most energy-saving defrost can take place. Regolatore per il controllo della temperatura – EKC D1. Between two defrosts the S5 temperature will become lower the more the evaporator ices up the compressor operates for a longer time and pulls the S5 temperature further down.

  COVENANT TAVIS SMILEY PDF

Temperaturregler – EKC D1. The signal to the thermostat, the alarm thermostat and the display can be set independently of one another. Only the function belonging to the selected application is shown.

During operating with a night time cover the difference 2022d1 to e.

The function is furthermore only relevant if you have chosen defrost with interval start d S4 limits can be set in A13 and A When all are in waiting position there will be a change-over to refrigeration.

All settings except for Application o61 and Address o03 will be copied. S3 This connection is primarily used when control is based on area.

If the function is used, access code 1 o05 must also be used. S3, S4, or a combination of them.

Continue session

Regulation is carried out when the input is short-circuited, and regulation is stopped when the input is put in pos. The heating element is activated Brine: Parameter o16 is expired Max Hold Time A8: Refrigeration control with one compressor The functions are adapted to small refrigeration systems which either may be refrigeration appliances or cold rooms.

Push the middle button until the parameter value is shown 4. System Management Electronic Controls: Digital input signal – DI1 The controller has a digital input 1 which can be used for one of the following functions: Module de passerelle EKC Showing of a negative figure spells problems.

The function will be active after each and every power failure. Time delay for cooling long alarm delay This time delay is used during start-up, during defrost, immediately after a defrost. In o17 the ratio is determined. Manual control of outputs 25 S Controller tray for refrigeration appliance control with TEV.

  E3X-A41 OMRON PDF

Alarm delay short alarm delay If one of the two limit values is exceeded, a timer function will commence.

Controles de temperatura para muebles y cámaras frigoríficas

Go to procurement section Procurement. All the R codes: When the door is closed again there will be a time delay of two minutes before the light is switched off. When the thermostat calls for refrigeration will the compressor relay be operated. There are two kinds of error reports – it can either be an alarm occurring during the daily operation, or there may be a defect in the installation.

The buttons When you want to change a setting, the upper and the lower buttons will give you a higher or lower value depending on the button you are pushing. Terms of Use Privacy policy General information Cookies.

Upper alarm limit Here you set when the alarm for high temperature is to start. Danfoss EKC D1 temperature settings The sensor is correct, i change the other ejc whit other freezer and the problem goes with the controller I went to the store and got a new one and the problem is solved.

Overriding of light diagram Only for use with circuit diagram 2 in which relay 4 is used to control the light By holding the middle button in for four seconds, the light relay will change over to the opposite position. The ekf value is set. Controlador de temperatura AK-CC manual.

If data communication is used, it is important that the installation of the data communication cable is performed correctly.

Posted in Art